高壓去毛刺清洗機長時間運作時，設備也會出現-些小毛病，當故障出現時，操作員只需根據不一樣故障現象，細心查找原因，及時解決疑問即可。下面咱們介紹一些高壓去毛刺清洗機多見的問題以及解決方法。

When the high-pressure deburring and cleaning machine operates for a long time, the equipment will also have some small problems. When the fault occurs, the operator only needs to carefully find the cause according to different fault phenomena and solve the problem in time. Now let's introduce some common problems and solutions of high-pressure deburring cleaner.

1、高壓去毛刺清洗機在作業的進程中假如呈現反常的尖叫聲，多見原因是因?yàn)殡姍C(jī)軸承缺油致使的。只要在電機的注油孔寫入普通黃油就可以解決，這種狀況出現的不多。咱們?cè)诟邏喝ッ糖逑礄C(jī)定時修理保護時給予彌補就可以了。

1. If the high-pressure deburring cleaning machine presents abnormal squeal during operation, the common reason is that the motor bearing is lack of oil. It can be solved by writing ordinary butter into the oil filling hole of the motor, which rarely occurs. We can make up for it when the high-pressure deburring washer is regularly repaired and protected.

2、高壓去毛刺清洗機在發動后，呈現壓力不穩定或時有時無，這里大都原因是高壓水泵或進水管路內吸入了空氣所致使的，這時需求查看水源的壓力是不是滿足，進水過濾器是不是阻塞，假如發現濾網阻塞,將濾網取下用水清洗就可以了。

2. After the high-pressure deburring cleaning machine is started, the pressure is unstable or sometimes absent. Most of the reasons are caused by the intake of air in the high-pressure water pump or water inlet pipe. At this time, it is necessary to check whether the pressure of the water source is met and whether the water inlet filter is blocked. If the filter screen is blocked, remove the filter screen and clean it with water.

3、高壓去毛刺清洗機在作業的進程中有必定的作業壓力可是調不到設備的額外壓力或者說壓力只停留在必定范圍內而不能上升，在這種狀況下，首要要判別高壓噴嘴的孔徑是不是匹配。如替換高壓噴嘴后壓力依然上不去，這時需求查看調壓閥是不是調到位了，假如在掃除這兩種狀況下故障照舊，這闡明泵內密封組件損壞或者是活塞損壞，這種狀況需求聯絡廠商幫忙修理。

3. In the process of operation, the high-pressure deburring washer has a certain operating pressure, but the additional pressure of the equipment cannot be adjusted, or the pressure only stays within a certain range and cannot rise. In this case, it is important to judge whether the aperture of the high-pressure nozzle is matched. If the pressure still cannot rise after replacing the high-pressure nozzle, check whether the pressure regulating valve is adjusted to its position. If the fault is still the same under these two conditions, it indicates that the sealing component in the pump is damaged or the piston is damaged. In this case, contact the manufacturer for repair.

4、高壓去毛刺清洗機在正常作業必定時刻后壓力下降，這種狀況首要要查看高壓噴嘴是不是嚴峻磨損。其次需求分別查看調壓閥和水泵內部的密封組件。

4. The pressure of the high-pressure deburring washer drops after a certain time of normal operation. In this case, first check whether the high-pressure nozzle is severely worn. Secondly, check the pressure regulating valve and the sealing components inside the water pump.

5、啟動設備后，高壓水泵沒有水射出，這種疑問需求專門的修理人員查看。大多數原因是進水流里閥不能打開造成的，假如掃除這種狀況下疑問照舊，那即是高低壓水路串聯了。

5. After the equipment is started, no water is ejected from the high-pressure water pump, which requires special repair personnel to check. Most of the reasons are that the inlet flow valve cannot be opened. If the problem remains the same under this condition, it is that the high and low pressure waterways are connected in series.

高壓去毛刺清洗機多見的問題以及解決方法已經講解完畢了，當然這只作為咱們的一個參閱意見，還是要根據實際情況來做一個解決方案才行，您對此有什么意見可以隨時來我們這里m.55232.cn提出交流！

The common problems and solutions of the high-pressure deburring washer have been explained. Of course, this is only a reference for us. We should make a solution according to the actual situation. If you have any suggestions, you can come here at m.55232.cn to communicate!